Numerical approach to analyze fluid flow in a type C tank for liquefied hydrogen carrier (part 1: Sloshing flow)

The demand for clean energy use has been increasing worldwide, and hydrogen has attracted attention as an alternative energy source. The efficient transport of hydrogen must be established such that hydrogen may be used as an energy source. In this study, we considered the influences of various parameters in the transportation of liquefied hydrogen using type C tanks in shipping vessels. The sloshing and thermal flows were considered in the transportation of liquefied hydrogen, which exists as a cryogenic liquid at ?253 °C. In this study, the sloshing flow was analyzed using a numerical approach. A multiphase sloshing simulation was performed using the volume of fluid method for the observation and analysis of the internal flow. First, a sloshing experiment according to the gas-liquid density ratio performed by other researchers was utilized to verify the simulation technique and investigate the characteristics of liquefied hydrogen. Based on the results of this experiment, a sloshing simulation was then performed for a type C cargo tank for liquefied hydrogen carriers under three different filling level conditions. The sloshing impact pressure inside of the tank was measured via simulation and subjected to statistical analysis. In addition, the influence of sloshing flow on the appendages installed inside of the type C tank (stiffened ring and swash bulkhead) was quantitatively evaluated. In particular, the influence of the sloshing flow inside of the type C tank on the appendages can be utilized as an important indicator at the design stage. Furthermore, if such sloshing impact forces are repeatedly experienced over an extended period of time under cryogenic conditions, the behavior of the tank and appendages must be analyzed in terms of fatigue and brittle failure to ensure the safety of the transportation operation.     

Finite-time adaptive fuzzy control for a class of output constrained nonlinear systems with dead-zone

The article investigates the finite-time adaptive fuzzy control for a class of nonlinear systems with output constraint and input dead-zone. First, by skillfully combining the barrier Lyapunov function, backstepping design method, and finite-time control theory, a novel adaptive state-feedback tracking controller is constructed, and the output constraint of the nonlinear system is not violated. Second, the fuzzy logic system is used to approximate unknown function in the nonlinear system. Third, the finite-time command filter is introduced to avoid the problem of “complexity explosion” caused by repeated differentiations of the virtual control signal in conventional backstepping control schemes. Meanwhile, a new saturation function is added in the compensating signal for filter error to improve control accuracy. Finally, based on Lyapunov stability analysis, all the signals of the closed-loop are proved to be semi-globally uniformly ultimately bounded, and the tracking error converges to a small neighborhood region of the origin in a finite time. A simulation example is presented to demonstrate the effectiveness for the proposed control scheme.     

基于误差估值累加开环校正的诱导式欺骗检测方法

诱导式卫星欺骗干扰可诱导航空器逐渐偏离预定航迹，难以被发现，因此及时有效地检测干扰是飞行安全的保障。在现有紧组合导航体制基础上，设计了一种基于误差估值累加开环校正的紧组合导航结构，并证明了其性能与传统闭环校正紧组合导航性能等效。在此结构中，将紧组合导航系统与自适应序贯概率比检测方法结合，提出了一种基于误差估值累加开环校正的诱导式欺骗检测方法，融合紧组合导航信息与其他不受欺骗影响的导航信息，构建欺骗检测统计量进行诱导式欺骗检测。仿真结果表明，开环校正结构可避免随时间累加的惯性导航系统误差所导致的组合导航滤波器发散问题，同时欺骗检测方法可进一步提高算法对“最坏”情形下微小诱导式欺骗的检测效果。     

Machine fault diagnosis with small sample based on variational information constrained generative adversarial network

In actual engineering scenarios, limited fault data leads to insufficient model training and over-fitting, which negatively affects the diagnostic performance of intelligent diagnostic models. To solve the problem, this paper proposes a variational information constrained generative adversarial network (VICGAN) for effective machine fault diagnosis. Firstly, by incorporating the encoder into the discriminator to map the deep features, an improved generative adversarial network with stronger data synthesis capability is established. Secondly, to promote the stable training of the model and guarantee better convergence, a variational information constraint technique is utilized, which constrains the input signals and deep features of the discriminator using the information bottleneck method. In addition, a representation matching module is added to impose restrictions on the generator, avoiding the mode collapse problem and boosting the sample diversity. Two rolling bearing datasets are utilized to verify the effectiveness and stability of the presented network, which demonstrates that the presented network has an admirable ability in processing fault diagnosis with few samples, and performs better than state-of-the-art approaches.     

Experimental study on the propagation characteristics of hydrogen/methane/air premixed flames in a narrow channel

This work is focused on the explosion characteristics of premixed gas containing different volume fractions of hydrogen in a narrow channel (1000 mm × 50 mm × 10 mm) under the circumstance of stoichiometric ratio. The ignition positions were set in the closed end and the middle of the pipeline respectively. The results showed that when the gas was ignited at the pipeline closed end, the propagating flame was tulip structure for different premixed gas. When the hydrogen volume fraction was less than 40%, the flame propagation speed increased significantly with the rise of hydrogen volume fraction, and the overpressure peak also appeared obviously in advance. However, when the volume fraction of hydrogen was more than 40%, the increase of flame propagation speed and the overpressure peak occurrence time varied slightly. Furthermore, when the ignition position was placed in the middle of the pipeline, the flame propagation speed propagating to the opening end was much faster than that propagating to the closing end, and there was no tulip shape when the flame propagates to the opening end. The flame propagating to the closed end appeared tulip shape under the influence of airflow, and high-frequency flame oscillation occurred during the propagation. This work shows that the hydrogen volume fraction and ignition position significantly affected the flame structure, flame front speed, and explosion overpressure.     

An adaptive sliding mode observer based near-optimal OER tracking control approach for PEMFC under dynamic operation condition

Tracking control of oxygen excess ratio (OER) is crucial for dynamic performance and operating efficiency of the proton exchange membrane fuel cell (PEMFC). OER tracking errors and overshoots under dynamic load limit the PEMFC output power performance, and also could lead oxygen starvation which seriously affect the life of PEMFC. To solve this problem, an adaptive sliding mode observer based near-optimal OER tracking control approach is proposed in this paper. According to real time load demand, a dynamic OER optimization strategy is designed to obtain an optimal OER. A nonlinear system model based near-optimal controller is designed to minimize the OER tracking error under variable operation condition of PEMFC. An adaptive sliding mode observer is utilized to estimate the uncertain parameters of the PEMFC air supply system and update parameters in near-optimal controller. The proposed control approach is implemented in OER tracking experiments based on air supply system of a 5 kW PEMFC test platform. The experiment results are analyzed and demonstrate the efficacy of the proposed control approach under load changes, external disturbances and parameter uncertainties of PEFMC system.     

Estimating long-term time-resolved indoor PM2.5 of outdoor and indoor origin using easily obtainable inputs

To evaluate the separate impacts on human health and establish effective control strategies, it is crucial to estimate the contribution of outdoor infiltration and indoor emission to indoor PM_2.5 in buildings. This study used an algorithm to automatically estimate the long-term time-resolved indoor PM_2.5 of outdoor and indoor origin in real apartments with natural ventilation. The inputs for the algorithm were only the time-resolved indoor/outdoor PM_2.5 concentrations and occupants’ window actions, which were easily obtained from the low-cost sensors. This study first applied the algorithm in an apartment in Tianjin, China. The indoor/outdoor contribution to the gross indoor exposure and time-resolved infiltration factor were automatically estimated using the algorithm. The influence of outdoor PM_2.5 data source and algorithm parameters on the estimated results was analyzed. The algorithm was then applied in four other apartments located in Chongqing, Shenyang, Xi'an, and Urumqi to further demonstrate its feasibility. The results provided indirect evidence, such as the plausible explanations for seasonal and spatial variation, to partially support the success of the algorithm used in real apartments. Through the analysis, this study also identified several further development directions to facilitate the practical applications of the algorithm, such as robust long-term outdoor PM_2.5 monitoring using low-cost light-scattering sensors.     

基准平面垂直断面法在爆破漏斗试验中的应用

系统阐述了基准平面垂直断面法在爆破漏斗试验中测量爆破漏斗体积的基本原理,并将隧道激光断面仪应用于金厂河矿1 750 m水平15^#采场底部切割巷道爆破漏斗试验爆破漏斗体积测量中。通过与传统体重法等计算法所得漏斗体积分析比较,结果表明基于隧道激光断面仪与3D Mine软件分析的基准平面垂直断面法实用性强、操作方便、结果直观可靠,达到试验预期目的。     

Topology optimization of flexure hinges with a prescribed compliance matrix based on the adaptive spring model and stress constraint

This paper focuses on the configuration design of flexure hinges with a prescribed compliance matrix and preset rotational center position. A new method for the topology optimization of flexure hinges is proposed based on the adaptive spring model and stress constraint. The hinge optimization model is formulated by maximizing the bending displacement with a spring while optimizing the compliance matrix to a prescribed value. To avoid numerical instability, an artificial spring is used as an auxiliary calculation, and a new strategy is developed for adaptively adjusting the spring stiffness according to the prescribed compliance matrix. The maximum stress of flexure hinge is limited by using a normalized P-norm of the effective von Mises stress, and a position constraint of rotational center is proposed to predetermine the position of the rotational center. In addition, to reduce the error of the stress measurement, a simple but effective filtering method is presented to obtain a complete black-and-white design. Numerical examples are used to verify the proposed method. Topology results show that the obtained flexure hinges have the prescribed compliance matrix and preset rotational center position while also meeting the stress requirements.     

Effect of Reynolds number and boundary layer thickness on the performance of V-cone flowmeter using CFD

The effect of Reynolds number and boundary layer thickness on the performance of V-cone flowmeter has been evaluated using computational fluid dynamics (CFD). The shear stress transport k-ω (SST k-ω) turbulence model has been adopted for closure. The performance of two V-cone flowmeters with different beta ratios (β) viz., 0.6 and 0.7 for a fixed vertex angle (ϕ) of 60° has been analysed as a function of Reynolds number (Re). The results show that the coefficient of discharge (C_d) increases with Reynolds number in the laminar and transition flow regimes whereas it is nearly constant in turbulent flow regime. From the results, it can be concluded that C_d is independent of Re for values equal to 4000 and beyond. Further, it is also seen that the performance of the V-cone flowmeter is not affected by the upstream boundary layer thickness if the velocity profiles having different boundary layer thickness are extracted from an axial distance of 10D and more are fed at 5D upstream of the meter. However, the meter is sensitive to the extracted velocity profile from an axial distance of 5D and uniform velocity profile being fed at 5D upstream. The value of C_d may be sensitive as a result of the pressure variation due to the obstruction.